Contents (Click To Jump)
- 1 What Are the Most Common Plumbing Issues in Murrieta?
- 2 How Does the Water in Murrieta Affect Your Plumbing?
- 3 How Much Does Plumbing Usually Cost in Murrieta?
- 4 Can Better Plumbing Save You Money in Murrieta?
- 5 When Should You Call the Water Utility Company in Murrieta vs. Hire a Plumber?
- 6 When Do You Need Permits for Plumbing Service in Murrieta?
What Are the Most Common Plumbing Issues in Murrieta?
Some of the most common issues we have handled in Murrieta include:
Water leaks are one of the most common plumbing issues in Murrieta. The calls we receive range from leaky faucets to toilets, showerheads, and pipes. Though some leaks are pretty obvious, like a dripping faucet, wet ground, or wall, others go unnoticed until much later when utility bills escalate.
Tank Water Heater Issues
Water heater plumbing issues have various causes, and in Murrieta, the primary culprit is water hardness. Hard water has a high calcium and magnesium concentration. Over time, the mineral deposits form a layer known as limescale. As the coating thickens, water-heating efficiency decreases and the heater consumes more energy to heat the water. The minerals also cause corrosion, leading to leaks as the heater ages.
However, tankless water heaters have lesser issues as they don’t store up water, which means less contact with the chemicals. This boosts their life significantly, up to 20 years, unlike the tank-type models, which require replacement every ten years.
Low Water Pressure
Whenever a client calls, complaining about low water pressure in their home, we get ready either to repair a leaky pipe or deal with a much bigger problem – limescale buildup. Some pipe leaks often go undetected, but as the water escapes through the holes or cracks, pressure decreases. On the other hand, limescale buildup narrows the pipes over time, which lowers the water pressure.
Blocked kitchen sinks, bathroom, and laundry room drain clogs are all common issues in Murrieta. While some clogs are due to debris lodging in the drains, others are caused by soap scum accumulation.
When cleaning detergents react with the chemicals in the water, they create a thick layer – soap scum. Usually, hard water like the water in Murrieta reduces the efficiency of detergents, necessitating the use of extra amounts. Eventually, high quantities of soap scum end up going through the drains, which then sticks to the pipes, causing blockages.
How Does the Water in Murrieta Affect Your Plumbing?
According to a U.S. Geological Survey (USGS) report, hard water is prevalent in the western United States. USGS measures water hardness based on the quantity of calcium carbonate per liter. 61 to 120 mg/l is considered moderately hard, 121 to 180 mg/l is rated as hard, while 181 mg/l and above is very hard. Murrieta’s water is between 121 to 180 mg/l, which is hard.
The minerals in hard water, mainly calcium and magnesium, build up in pipes and other plumbing fixtures, creating limescale layers. When limescale accumulates, it narrows the pipes, which then lowers the water pressure. The lines may also burst, especially when the pressure is too high. In showerheads, the buildup blocks nozzles.
The chemicals also corrode the pipes and fixtures, sometimes resulting in pinhole leaks. In some cases, the rust discolors the water, especially if it sits for too long.
Hard water also reduces the cleaning detergents’ effectiveness. As such, people often use more detergent to achieve the desired lathering. Eventually, too much soap scum ends up down the drain, which sticks to the pipes and clogs them.
Water heaters require regular maintenance and replacement, at least every ten years. But with hard water passing through the system, its performance decreases significantly. Issues of corrosion and subsequent leaks arise. Limescale buildup also hinders the heater’s efficiency by insulating its surfaces, thereby prolonging heating.
How Much Does Plumbing Usually Cost in Murrieta?
The plumbing cost in Murrieta depends on various issues, but it averages between $200 and $600. The type of task, materials used, labor costs, etc., are some common cost factors.
Cost Factor: Type of Task
The amount you pay for a plumbing job depends on the type of task involved. Usually, repairs cost less than installations since they require fewer materials and less time to complete. On the other hand, installations involve purchasing all the materials and often take longer to finish. Essentially, when costing a plumbing job, our plumbers consider the complexity of the task, then they factor in the time and expertise required.
For instance, bathtub installation might cost you between $1,500 to $2,000, while a toilet would go for $300 to $400. Replacing old pipes can cost between $1,000 to $2,500, while installing the drainage is slightly higher, averaging between $2,300 to $3,800.
Most repairs range between $100 and $1,000. However, significant works such as sewer line repair cost more, even to the tune of $3,000. Repairing a toilet will cost you between $180 and $250, while you’re likely to part with $400-700 for your water heater and $250-400 for a clogged drain.
Plumbing installation in a new home will cost you anywhere from ten thousand dollars to several tens of thousands depending on the home size and the amenities present – bathrooms, kitchens, pool, etc.
Cost Factor: Labor Costs
Our plumbers in Murrieta typically charge hourly rates. Overall, the amount you end up paying on labor will depend on the hours spent on the job. But, in some cases, our experts have a flat service fee, which acts as the minimum price. Emergency calls are also likely to cost higher than standard appointments.
Cost Factor: Materials Used
Another vital plumbing cost determinant in Murrieta is the materials used. Copper pipes are more expensive than plastic types. Using plastic pipes can end up saving you thousands of dollars, but copper pipes outlast them by far.
On the other hand, there are low-cost fixtures that can get you massive savings in material cost. However, if you decide to go for water-efficient fixtures, you may end up paying more. The latter use superior technology to achieve the same efficiency as standard fixtures while spending less water. Hence, the higher cost.
Can Better Plumbing Save You Money in Murrieta?
Though better plumbing may involve using high-quality materials and superior craftsmanship, which can be costly, you end up saving money in the long run. Some of the ways you can save money through better plumbing include:
For instance, installing water-efficient fixtures – faucets, high-efficiency toilets (HET), performance showerheads, etc. – may be costly initially. But they end up saving you money in utility bills (both water and electricity costs). Replacing your old fixtures with these can cut your water usage by 30%, which is massive considering it’s a month-to-month saving.
Even better, you can get WaterSense products and save even more. WaterSense-certified products save at least 20% more water than the standard federal requirement. According to the agency, water-efficient products have saved the nation 4.4 trillion water gallons in the past decade. In terms of water and heating costs, the savings are more than $87 billion. If you would like to know how much you can save, the U.S. environmental protection agency (EPA) has a tool for that purpose.
Water Heater Savings
If you have a tank-type water heater, installing a tankless model can reduce your water and electricity expenses significantly. Tankless heaters, also known as demand-type, do not require water storage. Instead, they warm water on the spot as it passes through. This ensures only the water needed gets heated.
If you’re used to turning the faucet or shower on to allow cold water to flow out while you wait for the right temperature, a tankless heater can save you the liters that go to waste. Alternatively, you can shorten the distance the water travels from the heater to the faucet or showerhead and ensure the piping has quality insulation to limit heat loss.
Pressure-Reducing Valve (PRV)
Most homes in Murrieta have relatively high water pressure levels, even to the tune of 80psi (pounds per square inch), which is the legal limit. The recommended pressure is between 60psi and 70psi. But you can use a pressure-reducing valve to cut this down to a lower psi to minimize water consumption. The pressure should not go down below 20psi to avoid water contamination, but keeping it at about 35psi is safe and efficient.
The distance between water points in your home can significantly impact the plumbing costs. You can save installation and repiping costs by designing the floor plan, keeping the amenities that require plumbing close together. For example, you can have the laundry room next to the kitchen, upstairs bathrooms above downstairs bathrooms, and so forth. This way, you get to use fewer materials, and the labor time in installation, repiping, or repairs decreases significantly.
When Should You Call the Water Utility Company in Murrieta vs. Hire a Plumber?
Distinguishing between the responsibility of utility companies and your responsibility as a consumer may seem like an obvious thing. But issues can get confusing sometimes, like when you happen to find a water puddle on your compound.
When to Call the Water Utility Company
- If there’s water leakage on the company’s side of the meter.
- If no water is flowing to your home.
- If there’s water interruption due to a burst pipe on the street.
When to Hire a Plumber
- If the water leak is on your side of the meter.
- If you have low water pressure and you suspect the pipes are leaking or clogged.
- If your meter keeps running even when all outlets are closed.
When Do You Need Permits for Plumbing Service in Murrieta?
In Murrieta, you require a permit before hiring a plumber for significant works like installations and remodels. Repairs and replacements do not require permits unless they involve altering the original plan. The same regulations apply to DIY plumbing projects.