Contents (Click To Jump)
What Are the Most Common Well Pump Repair Issues in Tyler?
Several issues affect well pumps in Tyler. The first one to consider is your water quality. If you have hard water, which is very common in Tyler, the high amounts of minerals can form deposits along the inside of your pipes and shorten the life of your well pump. If the build-up becomes serious enough, it can even negatively affect your water pressure. Suppose you’ve experienced water pressure changes recently. In that case, it could be due to a problem with the pump’s motor, or because of hard water mineral deposits, or another issue, so it’s a good idea to have your system looked at by our professionals.
A hole in the pressure tank‘s air bladder can cause another common repair issue. When this air bladder develops a leak, you can usually hear clicking sounds coming from the pressure switch near the tank. This is a good indication that some air has escaped into the pressure tank, which causes strain on the pump’s motor and can reduce your pump’s life expectancy. If you notice clicking sounds or unusual noises coming from your pressure tank, you should have it inspected by our professionals right away.
What Factors Cause Premature Well Pump Failure in Tyler?
For Tyler residents, a significant factor contributing to premature well pump failure is not following the recommended maintenance schedule, which involves having our professionals inspect your system every 2-3 years. The best way to ensure the longest operating life of your pump is to have it inspected and repaired regularly since many small issues can arise that can only be detected with the help of our experts.
For example, your well pump has a pressure tank that features an air bladder. If this bladder develops a leak, the pressure in the tank will slowly decrease, which strains the motor and causes your pump to start and stop frequently. Without regular inspections, you might never notice issues like this. If your well pump is located in an easily accessible area, you might be able to hear a clicking noise, which indicates that you have a leak. However, many pumps are located deep underground, making this impossible without the help of our professionals. In many situations where regular maintenance has been neglected, the first sign that something is wrong with the well pump is when it fails completely.
Another issue to look out for to prevent premature well pump failure is having your water requirements increase without adapting your pump system. The more water you use, the harder your pump has to work to deliver the water to your home, so you must choose a powerful pump to handle your water requirements for a long time.
If you have recently increased the number of people living in your home, or if you have purchased new appliances that rely on water to function, the demands on your pump will also increase, making it a good idea to reevaluate your current well pump’s capabilities. Certain plumbing issues can also contribute to premature well pump failure. Toilets that constantly run or dripping faucets cause the well pump to run constantly, delivering this water. This can be a significant contributing factor to the daily wear placed on your pump. If you have even minor plumbing issues, you should have our professionals resolve them in a timely manner.
How Much Does Well Pump Repair Usually Cost in Tyler?
Many factors influence well pump repair costs. Your pump’s complexity and age, its current condition, how much maintenance it received, and even your climate can affect your well pump’s performance and anticipated repair costs. In Tyler, costs fluctuate between $170 to $1,384, with the average cost being $766. These prices include the cost of labor and the average amount charged for replacement parts, materials, and the equipment necessary to perform the repair. Let’s take a closer look at the major issues that contribute to these differences in price.
Well Pump Type
There are two basic pump types, jet pumps, and submersible pumps. Jet pumps are used with wells that are 25 feet deep or less and are mounted above the ground. They rely on suction to draw water up to the surface and through the pipe system. If your property is located in an area with a high water table where the well doesn’t need to be very deep, there’s a good chance you have a jet-type pump. This kind of pump is generally less expensive to repair and maintain since they are easier to access than other kinds, and problems can be identified before they become more expensive serious issues.
The other type of pump is a submersible pump. This kind is used in areas where the water table is low, and a deep well is needed to access that water that’s far underground. In these situations, the pump is located underground and connected to a power source located on the surface. The pumps have to work harder to send water up through your pipes, and they are challenging to access. If there is a problem with the pumping mechanism, it can be difficult to detect since you can’t see or hear it from where it’s located. This means that repairs are more time-consuming and costly, and issues aren’t always noticed until they’ve become very serious. Maintaining a regular maintenance schedule is very important with submersible pumps.
History of Pump Maintenance
Since well pumps are typically located out of site, either deep underground or in areas you might not frequently spend time in, it can be difficult or impossible to notice a small problem on your own. If regular maintenance isn’t being performed in many situations, the first sign of something wrong well a well pump will be its complete failure. There aren’t many obvious signs of wear you can look out for without hiring our professionals to inspect the components.
For this reason, if you haven’t kept up with the recommended maintenance schedule, it’s more likely that the repair costs you can expect will be fairly high as they can be the result of multiple component failures. Private well systems involve many parts that can all cause potential issues for homeowners. The pump, its motor, or the storage tank are all potential problem sources, so it’s important to have your system regularly inspected by our state-licensed professionals.
Well Depth
Private wells are all unique based on their specific location and how much deep drilling was required to access the water. For areas where the water is located further underground, requiring a deeply drilled well, special, more powerful pumps are consequently required to get the water up to the surface and through your pipes. Detecting and repairing issues with deep wells is more challenging and expensive. The submersible pumps used in deep wells can be more costly to repair and can have shorter lifespans due to the strain and demands placed on them. For this reason, it’s also important that you choose a pump type that is designed to handle your unique water usage demands.
How to Avoid Costly Well Pump Repairs in Tyler?
The best way to avoid costly repairs is always to have your well pump regularly inspected by a licensed professional like us. Sticking to the recommended maintenance schedule is the best way to detect small issues before becoming bigger and more expensive. It can even extend the life of your pump, which can save you the cost of replacement for several additional years.
Lowering your water usage is another good technique for extending your pump’s life. The more a pump is used, the shorter its lifespan. This means getting running toilets, or leaky faucets fixed promptly because when these fixtures are running, so is your pump. You can also have your water quality tested and consider treating it as necessary. Hard water contains high levels of minerals that deposit themselves along the insides of your pipes and pump. Over time, they can build up enough to even cause a decrease in your water pressure and negatively affect your pump. Have our experts check your water quality, recommend any specialized pumps that might be required, and explain your water treatment options.
When Do You Need Permits for Well Pump Repair in Tyler?
The first step in determining if you need a permit for well repair is to make sure the problem is actually with the well pump itself. If it turns out that the water tank or pipe system is actually causing your issue, you might not require a permit to make those smaller repairs, or a separate plumbing permit might be required.
If it is your pump that’s the problem, you will need to hire our state-licensed well water contractors to handle the repairs, and typically we will be the ones who handle the permit process for you. In an emergency, such as if your pump is not functioning and no water is running to your house, section 2015 IRC R105.2.1 of the city municipal code allows us to obtain a permit in as little as one business day.
